Instructiones de nexu et operatio ad plures sentinam nexu
I. Non possumus coniungere maximum VI occidere de variabilis frequency aqua exhauriunt. Connection pro VI Sets de VFD aqua Pumps:
Coniungere ad CDLXXXV ostentationem tabernaculi terminatio in ostentationem tabula cum 2p funem. The 485+ and 485- of the first inverter terminal are connected respectively to the 485+ and 485- of the second inverter terminal, and then connect the second inverter to the third inverter, the third inverter to the fourth inverter, the fourth inverter to the fifth inverter, the fifth inverter to the sixth inverter in the same way. Observare iunctio ordine coniungere recte positivum filum connexa ad positivum filum negative filum coniuncta negativum filum.
II. Cum omnes cables sunt connexa et omnes variabilis frequency aquae exhauriuntur sunt powered on, posuit illa VI inverters ad subsisto statum per urgeat per "stop in sequentibus gradibus III et IV ut ex inverter ad haec gradus III et in se inverter ad haec gradus III et posuit in III et in sequentibus steps in III et ad machinam in sequentibus, et in III et in hoc apparatus in sequentibus gradibus, et in IV et in sequentibus, et in sequentibus gradibus III et in IV ad machinam in sequentibus.
III. Press "est" et "Down" button de primo inverter eodem in III seconds ad intrare ad subdiroriam, deinde ad I ad "Pump est ad Confirmare, et in Vfd aquae Pump est ad Confirmare, et quod Vfd est in Pump et in PRUSTO est" VFD est in Pump et ad Confirmare "VFD Aquae Pump I ad Confirmare, et in Servi Vfd est. (P022 est posuit pro situ numero)
4. Set the other 5 inverters according to step 3, set the second inverter to 2 (the second is the No.2 machine), the third to 3 (No.3 machine ), the fourth to 4 (No.4 machine), the fifth to 5 (No.5 machine), and the sixth to 6 (No.6 machine).
V. Intra in Subdirectory de primo inverter iterum et adjust ad P023, set ad cycle tempore secundum tuum requisita, ad Novifacta profecta range est {{II}}}}. For example, if it is set to 24 hours, set the parameter to 24. (P023 is the cycle time setting. Please note that if you want P023 works ,the parameter of P024 should be one less than the total quantity of inverters in the multipump connection. For example, if you connect 3 inverters, P024 must be 2; If you connect 2 inverters, P024 must be 1).
6. Enter the subdirectory of the first inverter again and adjust it to P024, set the parameter to 6 (indicating 6 inverters to be connected), set to 2 if you want to connect only 2 inverters, and so on (this is the case when you don't need P023 cycle time fonction; if you need cycle time fonction, the parameter should be one less as indicated in step5). (P024 est numerus machinis ut connected).
VII. Omnis occasus facto, dii omnes inverters potestatem copia. Et coniungere omnes inverters ad potestatem post II minutes.
VIII. Cum vides in "Group" indicator lumen unius ex inverters semper est in (hoc inverter est exercitum, altera V sunt servi, et "Group" indicator lux servi est coruscum). Si omnes "Group" indicator lumina in panel ex illis inverter sunt in, in nexu signum est normalis.
IX. Placere note ut dum operating panel, tantum bullarum de exercitum Panel opus, vos non operari alia servi 'panel. Torcular "Run" puga pyga in exercitum inverter et soleatus incipiunt currere, tum debugging est perficitur.
